This great article in the next paragraphs in relation to How to Install a Bathtub is without a doubt informative. You should check this stuff out.
![A Step-by-Step Guide to Installing a Bathtub](https://i0.wp.com/www.projectsmallhouse.com/blog/wp-content/uploads/2020/01/OVE_Decors-980208275-Ruby.jpg?resize=500%2C347&ssl=1)
Setting up a bathtub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is easily easily accessible, the job can move quickly; if you need to open a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the new one. Ensure you have certified on your own for the task and fit attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is better to consider using one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will aid you mount a brand-new bathtub in your restroom if you have actually already bought a new bathtub and do not need to change the setup of your previous water system pipelines.
Your devices and product list should consist of the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Chisel
- Tape Measure
- Pipe Caps
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before moving on to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the manufacturer given backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former type should be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, put the bathtub in the needed placement. The wood boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little points.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit the bottom of the furthest versatile tap port to the ideal supply pipeline by making a compression join; after that do the same for the various other faucet.
Activate the water system and also check all joints and new pipework for leaks and also tighten them if required. Load the tub as well as additionally examine the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the tub needs to wait up until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installation
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, creating the water to permeate the wall surface between the bath and the tiling, bring about difficulties with dampness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealer can fracture relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![A Step-by-Step Guide to Installing a Bathtub](https://images.thdstatic.com/productImages/6d986c87-441f-420b-88ff-bb5b315b7933/svn/white-kohler-alcove-bathtubs-k-721-0-e1_600.jpg)
I hope you enjoyed our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking time to read through our blog. Liked our piece? Please share it. Let others locate it. Thank-you for going through it.
Expert care? Call.
Comments on “Plumbing Basics: A Prerequisite for Installing a Bathtub”